Maa-alune üldine toru galerii kokkupandavate komponentide tootmisprotsess üksikasjalik
Esiteks, koha seaded
Kokkupandav koht
1. Sait on valitud vastavalt projekti tegelikule olukorrale. Kohas kasutatakse kinnist haldamist impordi ja ekspordi loomiseks ning ehitustee juurdepääsutee on reserveeritud ala planeerimisel ning eeskirjade kohaselt imporditakse ja eksporditakse erinevaid märke.
2. Ettevalmistuskoha paigutus peab olema rangelt kooskõlas standardvarustuse nõuetega, vastama töötervishoiu, tööohutuse ja keskkonnajuhtimissüsteemi nõuetele ning HSE ekspluatatsiooni juhendile ning kehtestama mitmesugused ohutuskeskkonna kaitsevahendid. See peab olema täielikult varustatud ohutu ja tsiviliseeritud tootmise, reovee ärajuhtimise ja prügivedu nõuete täitmiseks. Rangelt vastavalt kohalike omavalitsuste talituste asjakohastele sätetele.
3. Puhastage kokkupandav koht, tasandage, vibreerige ja tihendage, paigaldage 20 cm paksune tsemendiga stabiliseeritud kivimaterjali alus, tasandage ja vibreerige ja tihendage. Taime peamine tee valatakse tsemendiga stabiliseeritud kivimaterjali baasil 15 cm paksune kommertsbetoon C20. , paigaldusala, eeltöötlemine, tootmispiirkond, integreeritud torude galerii looduskaitsealade paigaldusala, mis valatakse kommertsbetoonist 10cmC20. Pidurikraanide rööbasteedel on kaevamissügavus 60 cm, betoon valatakse ja rull asetatakse. Tehke ka need kolm asja:
(1) Saidist tuleb puhastada ja tasandada, sealhulgas kokkupandavad alad, ehitustööriistade ja olemasolevate transporditeede ühendused ning kokkupandavad kohad.
(2) Eeltöödeldud alal tuleb puhastada ehitusmasinate läbipääsu või ehitust mõjutavad kivid, umbrohi, puud, ehituskonstruktsioonid jms, kraavi ja kraavi tuleks tasandada ja madalal asuvad piirkonnad akumuleeritud vesi tuleks tühjendada ja vajadusel muuta. Täitke, tagage täiesti maa tasakaalu ja kandevõime ja survejõu maht.
(3) Ettevalmistuskoha puhastamine ja nivelleerimine viiakse läbi selleks, et vältida maa omandamist või maakasutust, liikluse takistamist, hoonete, rajatiste, mälestiste jms kahjustamist, et vältida keskkonnasaastet ja mullaerosiooni.
4. Terasest riba töötlemise ja paigaldamise ala ettevalmistus, integreeritud torukujunduskonstruktsioonide valmistamise auru ala, integreeritud torgalerii looduskaitsealune ruum, integreeritud torude galerii hoiukoht ja muud funktsionaalsed alad. Kontoripind ja elamispind määratakse vastavalt tegelikule olukorrale ning kokkupandav põllu sissepääs ja väljapääs asuvad valveta ruumi. Teiseks tootmisprotsess
Tootmisprotsessi voolukava
1. Ehitusseadmete ehitusmaterjali tugevdamine, proovivõtmise kontroll, terase töötlemine, terasest riba sidumine, paigaldamine.
(1) tugevdamise lähenemise kontroll a. Rebar on kuumvaltsitud HPB300 klassi terasest ja kuumvaltsitud HRB400 klassi terasest riba. Terasest riba standardkindlus vastab GB50010-2010 4.2.2 nõuetele. Ribastatud terasest riba vastab raudbetoonist terasele: II osa: kuumvaltsitud ribadest terasest vardad (GB1499.2-2007); kergestised terasvardad vastavad raudbetoonist terase nõuetele: I osa: kuumvaltsitud terasest ribad (GB1499.1-2008). Terasplekk on valmistatud Q235-B terasest, keevituselektrood HPB300-klassi terasest keevitatud E43 tüüpi elektroodiga ja HRB400-klassi teras on keevitatud E55 tüüpi elektroodiga. b. Enne, kui teras siseneb saidile, kontrollige sordi, kvaliteedi, spetsifikatsiooni, koguse ja materjalide nimekirja rangelt vastavalt nõuetele, olenemata sellest, kas toote kvaliteedi sertifikaat, tehase kontrolli aruanne ja uuesti kontrollimise aruanne on täielikud ja kehtivad. Mehaaniliste omaduste test peab vastama asjaomastele standarditele. c. Enne terase sisenemist põllule ja enne kasutamist kontrollige terasest riba välimust, kas see on sirge, pole kahjustusi, pinnale ei kuulu räbu, ei ole rasket nahka, pragu, õlivärv, teraline või teraline räst, ühtlane värv , vaadake teraslehe läbimõõtu. Vastake nõuetele, et mitte mõjutada terase tugevust ja ankurdamist. Terasplekke, keevitusvardaid jne kontrollitakse enne terasesse sisenemist teraskonstruktsiooni kontrollimisega.
(2) Terasvarraste ladustamine a. Territooriumile sisenevad terasvardad ladustatakse terasest baaride hoidlas vastavalt sordi, spetsifikatsiooni ja klassi nõuetele. Materjalid ladustatakse materjali töötajate ja hooldajate poolt. Rooste vältimiseks peab terasest riba olema kaetud padjaga. b. Kontrollige, kas terasest baaril on tehase sertifikaat, tehase kontrolli aruanne ja uuesti kontrollimise aruanne. Kontrollige välimuse kvaliteeti ja mahtu esindava läbimõõduga. Terasekaarti tuleb kvaliteediindeksi abil põhjalikult kontrollida. Partii kontrolli kohaselt on läbimõõt ja kaalu kõrvalekalle sama kui sama tehas, sama ahju number, sama spetsifikatsioon, sama tootmisprotsess ja sama ehitusplatsi samaaegselt sisenev 60-tonnise terasvarras inspekteerimispark vähem kui 60 tonni. Proovitava proovina võtke ka proovile. Terasvardade proovivõtmist teostab järelevalvet teostav insener. Kaks terasvarrasse võetakse kaks katsekeha, mille pikkus on umbes 450 mm ja kaks külmkindlat katsekeha, mille pikkus on ligikaudu 350 mm, katsekasti paigutatud ja seejärel jälgitakse tihendamist või seiret katseruum. Kui uuestihindamise aruande tulemus on kvalifitseerimata, tuleb seda teha kahekordselt ja uuesti testida. Uuesti läbivaatuse aruande tulemused peavad olema kvalifitseeritud ja kutsealase järelevalve insener allkirjastab tüübikinnituse ning terasvarraste partii võib töötlemisel kasutada. Muude materjalide ladustamine ja ladustamine toimub niiskusolatsiooniga.
(3) Rebara töötlemine Enne töötlemist, vastavalt projekteerimisnõuetele ning pikkusele ja kogusele kombineerituna erinevate töötlemisviisidega, määratakse iga rebari pikkus täpsuse tagamiseks arvutusega. Töötlemise ajal kontrollige, kas blanking tabelis on viga või väljajätmine. Kontrollige materjali tabelit igat tüüpi terasvarraste jaoks. Pärast neid kahte kontrollimist vajutage tegelikku näidist vabastamiseks materjalide tabel. Pärast katsetootmise kvalifitseerimist saab seda partiidena töödelda. Hea teraslatid tuleks korrastada korrapäraselt. Terasest riba pind peab olema puhas ning enne kasutamist tuleb puhastada määrded, mustus ja rooste. Terasplekid sirgendatakse ja mehaaniliselt sirgendatakse. Pärast sirgendamist terasvardad ei tohi paikneda painde, surnud painutatud või väikesed lained. Terasest riba lõikamine peaks põhinema terasest riba numbril, diameetril, pikkusel ja kogusel. Terasest riba pikkus ja pikkus tuleks katki ja lühike materjal tuleb kõigepealt katki lõigata ja lühike teraspea tuleks võimalikult vähendada ja lühendada, et säästa terast ja vähendada kaotust. Kui terasplekk on painutatud, määrab väljapoole paindejoon ja määrab paindenurga, mis põhineb iga terasest tõmbevõtu tugevusel. Enne formaalset painutamist katsetatakse suurtes kogustes painutatud terasvardad katseprotsessi katmiseks ja asjakohased tehnilised andmed määratakse kindlaks enne partii paindumist. Kui terasest riba on painutatud, moodustab kaar kaar. Pärast painutamist ei ole suurus suurem kui väljalõike suurus. Pöörde reguleerimise väärtust tuleks kaaluda. Pööratud terasvarda painutusprofiil D ja keskmise osa painutamine on vähemalt 50 korda terasvarda läbimõõduga. Terastrossi pikkust tuleks kõikehõlmavalt käsitleda komponendi suuruse, kaitsekihi paksuse ja terastraadi painde reguleerimise väärtuse järgi. Terasest riba töötlemise lubatav kõrvalekalle ei tohi ületada spetsifikatsiooni. Ebapiisava valmismaterjaliga terasvarraste puhul kasutatakse suu pikkuse tagurdamiseks ja seejärel painutamiseks tihendusrõhu keevitusmeetodit. Lõplikke keevitajat tuleb koolitada spetsiaalse põkk-keevitusprotsessi käigus ja kontrollida. Pärast erinevate terasvarraste moodustamist ei tohi lubatav hälve ületada spetsifikatsiooni: jõupiirde täispikkus peab olema ± 10 mm; jalutuskeha iga osa pikkuse kõrvalekalle on ± 5 mm; painutatud ribide hälve peab olema ± 20 mm liite suurest mahust, betoon on ± 30 mm; terase nurga kõrvalekalle on 3mm; 6-12mm ümmargune riba on valmistatud jalatsist ja lõpukonksu pikkus on 75 ~ 105mm vastavalt põhiriba läbimõõdule. Kindlaksmääratud arvutus enne väljalaskmist määratakse töödeldud terasvarraste klassifitseerimiseks ja ladustamiseks ning moodustunud terasvarraste ladustamise ja transportimise ajal ei saa deformeeruda.
Põlvekarkass (tugevdatud teras) terasest raketis
Raskused: ristkülikukujulise ülemise toru peamised ribid on raskused ristlõike põhiribal. Iga rõngas koosneb neljast terasest vardast, millel on kaks kaarut, millest igaüks moodustab ristkülikukujulise ristlõikega ülemise toru. Kaare raadius on liiga väike, kaarduskaare segment on lühike ja täpsus on kõrge. . Lahendus: enne, kui terasvardad on painutatud, märkige need iga kaare ristmikul. Siis on R90 kraadi kaar painutatud kolme rulliga ja sirgjooneline segment pole painutatud. Kui kaar on täielikult painutatud, pannakse see standardse peainspektsiooni. Kui nõuded on täidetud, liigub liikuva ratta liikumise positsiooni tähis paindemasinate tööplatvormile järgmise kiire tootmise jaoks. Kolme pöördega painutusmasinal peab olema liikumine ja tagasikäik. (4) Terasest keevitamine Valmistatud terasvarras asetatakse keevitustööde joonistele vastavalt keevitustööriistale terasest keevitamise tööriistale. Keevituskvaliteet on tähtis roll terasest riba üldise tugevuse tagamiseks. Terasribade töötlemise tehases puhastatakse terasvarras peamiselt kahepoolse välguga varustatud keevituskinnitusega, et puhastada nurgaharjad ja lõpuks pinna korrosioon, õlivärvid ja oksiidkile enne keevitamist ning metalli läige kuumtöötlemisel ja oksüdeerumise nähtus puudub. Samal ajal tuleks terase riba otspind hõlbustada hea kombinatsiooni hõlbustamiseks. Mõlema külje kinnituskohad peaksid olema joondatud, et tagada, et kaks terasvarrasid asetsevad samal teljel, ja kahe terasvarraste kohalik puhastus ei ole suurem kui 3 mm. Keevitamise ajal rakendatav rõhk peab olema ühtlane ja tugev ning temperatuuri tuleb reguleerida 30-40 MPa sõltuvalt terasest riba läbimõõdust, et saavutada hea haardumine kahe terasvarraste vahele. Kui erineva läbimõõduga terasvardad on keevitatud keevitatud, ei tohi hälve ületada 7 mm. Pehme keevitamine ja kohapealne keevitamine on rangelt kooskõlas eeskirjadega ja keevitustöötajad on sertifitseeritud töötama. Kui keevitamine on lõpetatud, muudetakse klambri vabastamiseks liigend valgeks mustani ja terasest riba tõmmatakse sujuvalt välja, et vältida paindumist. Pärast terasvarraste keevitamist lõpetatakse keevitatud liigeste välimuse kontrollimine õigeaegselt ja visuaalse kontrolliga mitteseotud liigesed tuleb uuesti keevitada. Kõik keevitamise operaatorid peavad tagama, et kõik keevitusseadmete liigid on heas töökorras, juhtida erinevate keevitusseadmete peamist jõudlust ja parameetreid õigeaegselt ning valima parameetrid tegelikuks tööks vastavalt mitteväärismetallide tingimustele ja ilmale, et tagada keevitamise kvaliteet. . (5) Tugevdatud terasest puurid tuleks enne spetsifikatsiooni, suuruse, kuju, koguse, positsioneerimisseadiste jms ümberkalifitseerimist ning põhjalik kontroll peaks toimuma vastavalt jooniste ja koostisosade loetelule. Disaini, koostisainete loendi ja füüsilise objekti saab sobitada. Turvalisus. Enne süsteemi paigaldamist paigutatakse armatuur paigaldusanduriplokile vastavalt projekteerimisandmetele. Samas määratakse kindlaks asukoha järgi püsiva sarruse seade, mis tagab, et pärast paigaldamist paigaldatud terasvardad vastavad nõuetele. Turvalisusprotsessis on terastraat valmistatud peamiselt traatühenduse ja kohapealse keevitamise teel. Avad on valmistatud 20 ~ 22 # juhtmest. Seondumis- ja sidumismeetod vastab spetsifikatsioonidele ja eeskirjadele. Spot-keevitust kasutatakse peamiselt terasvarraste ja seibide valmistamiseks. Fikseerimine, kohapealne keevitus peaks olema kindel, punktid peaksid olema ühtlaselt jaotatud ja jõupiirdeid ei tohiks tõsiselt kahjustada. Terasest riba kinnitusliit peab vastama järgmistele nõuetele: a. Süvistuse pikkus peab olema terasleibi painutamise ajal terasest riba läbimõõduga vähemalt kümme korda suurem, ja tihend ei tohi paikneda komponendi maksimaalse paindemomendi juures. b. Pingutustsoonis tuleb I-klassi terasest sidumisliide lõpuks konksu sisse tõmmata. Samal lõigul peab pingutustsooni liigendi ristlõikepindala olema väiksem kui 50% jõu vastuvõtva liigendi kogupindalast ja sidumisliides ei tohi olla suurem kui 50%. Mitte rohkem kui 25%, samal ajal ei tohi tihendusliidud tihendustsoonis ületada 50%. c. Tugevdatud liigesed, mis on kinnitatud traadi külge keskel ja mõlemas otsas. d. Pingutatud ribide ühised asendid on üksteisest võrdsed. Pingutatud terasest tugevdatud liigeste ringi pikkus peaks vastama konstruktsiooninõuetele. Keevitatud terasest vuugid ja mehaanilised ühendused tuleks asetada minimaalsele paindemomendile ja lohistada. e. Kui pingutatud terastraadi läbimõõt on ≥ 25 mm, pole soovitatav kasutada mitte keevisõmblusi. f Pingestatud terasest betoonist kaitsekihi paksus peaks vastama konstruktsiooninõuetele. Terasest riba õige positsiooni tagamiseks on see kinnitatud ja paigaldatud vastavalt projekteerimisnõuetele. g. Armatuurpuuride seostumisprotsessis on üks ΦPVC toru eelnevalt murtud liitmiku neli külge, Φ14mm, määratakse PVC toru pikkus vastavalt liigese suu seina paksusele ja eelmainitud PVC toru kasutatakse kontroll-auku ja süstimisava. Tõsteavad on paigaldatud integreeritud torukujunduse vasaku ja parema külje keskteljele 500 mm üles ja alla. Terastraadile on keevitatud kaks Φ125 * 10mm * 220mm terastoru ja tihendamiseks kasutatakse Φ140 * 4 terasplaati. Enne tõstmist on paigaldatud Φ125 * 10mm * 180mm terastoru. Φ110mm * 350mm rauast tihvti kasutatakse integreeritud torukujulise toruliitmiku tõstekonstruktsioonile vastava integreeritud toru kanderihmaga. Tugevdatud terasetööd on varjatud projektid. Enne betooni valamist tuleb terasest vardad ja sisseehitatud osad kontrollida ja aktsepteerida ning varjatud tehnilised andmed tuleb teha. Pärast kohapealsete inseneride nõusolekut saab järgmise protsessi teostada.
Terasvormide komplekt
Kõige tõhusam meetod kogumisprotsessis peaks olema: esmalt toetage sisemist hallitust, tuleb kõigepealt keevitada terastraami ühendusribid ja seejärel asetada põhjas hallitusseeni ja pistikupesa vooderdisega ühendatud ribid tuleks keevitada pärast terast raami pannakse hallitustesse ja terasvardad keevitatakse. Pärast seda, kui skeleton pannakse hallitusseeni, keevitatakse sissevooluava, soonega auk ja eelnevalt paigaldatud terasplaat. Pärast keevitamist on välismall koondatud. Tõsteava avanemise ebatäpsuse vältimiseks kinnitatakse tõstemehhanism välisvormile ja välimine hall vorm on monteeritud ja seejärel ettevalmistatud keevituspesa. Maetud terasest rõngas (6) tugevdatud kaitsekiht Betooni kaitsekiht on valmistatud betoonist plokist, paksus on võrdne kavandatud kaitsekihi paksusega, ploki suurus on 3 cm × 3 cm, plaadi number on suurem kui C25 mördi tugevus ja Kuivatamine tugevdatakse tootmise ajal, et saavutada disaini tugevus. 85% ülaltoodust võib kasutada. Kui vertikaalses konstruktsioonis kasutatakse, saab 20 lahtris olevat sidumisliini maha blokeerida ja plokk on kinnitatud traadi külge terasest riba külge. Alumise plaadi alumine kiht ja seina tugevduskiht asetatakse ühe ruutmeetri ruutmeetrile ja ploomide õied on paigutatud. Paigalduste vahekaugus peaks olema korralikult krüpteeritud. Paigaldage plokid mõistlikult ja laske need kindlalt kinni pingutatud terasest vardadesse, selle asemel, et asetada pinge all olevatele küüntele, peaks kinnitus olema kindel, et vältida niiskust ja libisemist valamise ajal; kas plokid on täielikult kontrollitud enne betooni väljavoolu kadumist või kahjustumist. 2. Betooni valamine (1) Betoonmaterjal Betoonitransport viiakse valmisvalmistamiseks betooni tankeriga ja pumbatakse lattu betoonipumba veokile. Betooni langus on üldjuhul 140-180 mm (konkreetne väärtus sõltub päeva temperatuurist). 4 betoonist vibreerivad vardad, mille vibreeritav raadius on 20-25 cm, nii et iga varda vahekaugus on 40 cm. Iga varda sügavus on 5 cm allpool eelmist vibreerivat pinda ja vibreeriv aeg pulgale on 2-3 minutit. (2) Segamissuhte kujundamine ja katsetamine a. Segamissuhte kujundamine Et vastata betooni konstruktsioonitugevusele, külmakindlusele, läbilaskvusele, liivagregaadi paisumiskiirusele ja ehituslikule töövõimele, on betooni ehitusmehhanismide optimeerimise katse Samas vastab see ehitus-veekindluse suhte ja languse nõuetele, ning seda kontrollib ja kinnitab järelevalveinsener. Betooni segu suhe peab tagama, et saadud betoon vastab konkreetsetele valamise tingimustele ja veetarbimine betooni segamissuhtes on võimalikult väike. b. Betooni segu suhte test betooni segu suhte testplaan, sealhulgas betooni segu suhte test ja erinevate tugevusklasside betooni jõudluskatse, segu suhte test 14d enne erinevate segu suhte testkomponente ja segamine, vormimine ja hooldus jne. Segu suhte testplaan teatatakse järelevalveinsenerile. c. Ehitussegu suhtekontroll Vastavalt seguhalduskatsele ja järelevalveinseneri poolt kinnitatud partiide nimekirjale kontrollitakse betoonisegude suhet ja kogu vee tarbimist reguleeritakse vastavalt agregaadi veesisaldusele. Betooni langus sõltub struktuuriosa olemusest, armeerimiskiirusest, betooni transpordi ja valamise meetodist ning kliimatingimustest ning kasutab väikest langust nii palju kui võimalik. Betooni langus vastab SL677-2014 nõuetele. (3) Betooni proovivõtmise test Betooni valamise protsessi käigus viib töövõtja proovide võtmise proovide proovide võtmise proovile vastavalt väljundi SL352-2006 sätetele ja järelevaataja juhenditele väljutusava ja valamispaigas ning esitab järelevaatajale järgmised materjalid : a. Ja selle integreeritud torupaigaldise kvaliteeditõend; b. Katsekeha koostis, segamine ja mõõtmed; c. Katsekeha ettevalmistamise ja hoolduse kirjeldus; d. Testi tulemused ja kirjeldus; e. Erineva vanusega betoon Katsetulemused nagu puistetihedus, survejõud, tõmbetugevus, lõplik tõmbetugevus, elastsusmoodul, Poissoni suhe, langus ja algseade ning lõplik seadistusaeg. (4) Betooni valamine a. Kombineeritud betooni segu suhe peab vastama DL / T5330-2005 "Hübriide-betooni segamissuhtluse spetsifikatsioonile" nõuetele ning kasutama tsemendi- ja veetsoolainet suhteliselt varase esialgse seadistamise aja ja varase tugevuse suurenemisega pärast lõplikku seadistamist. Erinevad lisandid, nagu õhu hõõrdumisagens ja varajane tugevusagent, peaksid arvestama betooni transpordi pikkade vahemaadega, suurendama betooni varajast tugevust, vähendama lammutamise aega, lühendama ehitusperioodi ja eelkõige lahendama betooni tugevuse aeglast kasvu talvel ehituses . Saidi betoonlanguse probleemi tuleb kontrollida 140-180 mm juures. b. Pärast seda, kui tehnikud on kvaliteedikontrolli ja -järelevalve teostamiseks paigaldanud ja kvalifitseerinud hallituse ja terasvarraste ning kinnitasid, saab valatud torude galeriid valada. Ava kõrgus on 2 meetrit või rohkem maapinnast ja tilk on 2 meetrit või vähem. Pehme nööriga tünn on asetatud suudme külge, et betooni kukkumiskõrgus oleks alla 2 meetri. c. Betoontorude tunnelbetoon võtab vastu sümmeetrilise valamise meetodi, et välja arvata, et serva kõrgus ei tohiks olla üle 40 cm, ja pidevvalu meetodiga konstruktsioon ei tohiks olla vahelduv. d. Betoon valatakse kihtidesse, teatud suunas ja teatud paksusega. Betoon on horisontaalselt kihiline ja kihi paksus on 30-40 cm. e. Vibraator kasutab pistikuga vibreerivat varda, liikuv kaugus ei ületa 1,5 korda vibreeriva riba tegevuse raadiust ja hoiab külgvormilt 5-10 cm kaugusel. Kui vibreeritakse, asetage betooni alumine kiht 5-10 cm, ja pakutage aeglaselt vibreeriba pärast iga vibratsiooni. Vibratsiooni ajal vinguta raketist, terasest varblast jms; iga vibratsiooniosa puhul peab see olema vallandatud, kuni betoon on tihendatud, see tähendab, et betoon peatub hukku, ei ilmne mullid, pind on tasane ja porine. Valamisprotsessi vältel tuleb iga töö tüüpi korraldada, et kontrollida terasvarraste, sulgude ja šabloonide muutusi ning olukorda tuleks käsitleda õigeaegselt. 3, kasti tõmbehooldus ja eemaldamine
Karburaht on valmis
(1) Pärast betooni valamist, pärast betooni esmakordset paigaldamist, aurutatakse integreeritud torupaigaldust kõrgel temperatuuril. Aurutamine võtab spetsiaalse aurukatte ja integreeritud torukujulise hallituse vorm on kaetud aurukatega ja aurukate põhi on tihendatud, et vältida auru väljutamist aurutamisprotsessi ajal. Aurukatelde aurutatakse keskkonnasõbraliku auruvõimaluse jaoks. toetus. Aurutamise käigus jaguneb see neljaks etapiks: staatiline peatus, soojendus, püsiv temperatuur ja jahutus. Staatilisel peatumisel tuleb ümbritsevat temperatuuri hoida allpool 5 ° C ja temperatuuri tõusu tuleks reguleerida 15 ° C / h. Püsiv temperatuur: kui temperatuur tõuseb 60 ° C-ni, võib aurutamist peatada pärast nelja tunni püsivat aurutamist. Jahutus: aurustumisavade integreeritud torude galeri jahutuskiirus on väiksem kui 10 ° C / h ja integreeritud torude galerii pinna temperatuur ei ületa 5 ° C, nii et integreeritud torude galeriid saab eemaldada aurutatud kate. Aurutamisprotsessi ajal on spetsiaalsed töötajad korraldanud temperatuuri tõstmise ja langemise efektiivse juhtimise ja detailide salvestamise. Esiteks, pärast seda, kui integreeritud toru galerii valatakse ja seiskub 2 tundi, on algselt seatud sisse integreeritud toru galerii ning kontroll ei esine kõrvalekaldeid. Aurutatud kate ja seadmed viiakse kokkupandava tootmispiirkonda ja aurukatetega on paigaldatud torude galerii. Rangelt suletud, kontrollige aurutamisseadmete ja aurukatete tihendamist ja puhastage aurutoru. Kui kõik ettevalmistused on paigas, alustage aurutamisseadet kuumutamiseks ja pöörake tähelepanu kütmistemperatuuri reguleerimisele 15 ° C / h ajal kuumutamise ajal. . Keelatud on soojeneda liiga kiiresti või liiga aeglaselt, mis mõjutab integreeritud toruliidri survetugevust ja toimivust. Kui temperatuur tõuseb 60 ° C-ni, käivitub pidev temperatuur auruga. Pärast pidevat aurutamist nelja tunni jooksul võib aurutamist peatada. Pärast püsiva temperatuuri aurutamist lõpetatakse integreeritud torude galerii auruvabrikus jahutamiseks ja jahutamiseks ning jahutuskiirus on rangelt kontrollitud. Temperatuur langeb 10 ° C / h jooksul integreeritud torude galeri pinnatemperatuurini ja ümbritseva õhu temperatuur ei ületa 5 ° C, aurukate saab eemaldada ja integreeritud torude galerii lammutatakse ja viiakse looduskaitse alla looduslikule kaitsele surnud. (2) Aurutamise lõppedes jõuab torude galerii eemaldamine ja looduskaitselise hoolduse plaan 50% -ni disaini tugevusest ning aurukatte sise- ja väliskülje temperatuuride vahe pärast peatumist ei tohi olla üle 5 ° C aurutamist ühe tunni jooksul. hallitust Väljatõmbamise järjekord on seest ülespoole, ülaosast allapoole. Lammutamisprotsessi käigus tuleb see samm-sammult eemaldada, hallitust eemaldatakse, integreeritud torude galeriid ja põhjavorm eemaldatakse portaalkraanist ja transporditakse määratud loodusliku kaitsehoones looduslike jootmine. Väljatõmbamisprotsessi vältel on malli all trafarettil rangelt keelatud kasutada lohu. Kui looduslik hooldus jõuab 75% -ni disaini tugevusest, eemaldatakse integreeritud torude galerii looduslikust kaitsekihist tagurpidi. (3) Toru galerii kokkupandav ja paigutatud plaan Pärast betooni valamist on disaini tugevus 50% ja pärast aurutamist ühe tunni vältel seisma, ei tohi aurutatud aiaga seest ja väljast vaheline temperatuuri erinevus olla suurem kui 5 ° C ja hallitust saab lammutada. Väljatõmbamise järjekord on seest ülespoole, ülaosast allapoole. Lammutamise käigus tuleb see samm-sammult eemaldada. Pärast vormi eemaldamist tõmmatakse valmistooted ja põhjasvorm vormist välja ja transporditakse määratud looduskaitsealusse looduslikuks jootmiseks. Väljatõmbamisprotsessi vältel on malli all trafarettil rangelt keelatud kasutada lohu. Tõste- või trossikontakti nurkad osad on kaitstud tõsteprotsessi ajal kerge ja kergega ning kõik tegevused on suunatud spetsiaalse isikuga. Kui toote tugevus jõuab 75% -ni disaini tugevusest, viiakse toode lõpphinnapärastesse looduskaitsealadesse. Transportimisel tõmmake toode laualt välja ja libistage toode. Selleks, et hõlbustada toote ladustamist, viiakse toote originaaltoote põranda põhja ja toote säilituskõrgus on kaks kihti. 4, suletud vee katsetamise standardid
Suletud veekontrolli voolukava
(1) Integreeritud torustikus olev vee sissepritse Enne vee sissepritse integreeritud torude galeriiplokk suletakse ja suletakse. Pärast kontrolli läbimist siseneb vesi sisse integreeritud torude galeriisse. Vesi siseneb integreeritud torukujunduse alumisest otsast. Pärast vee täitmist imendub integreeritud torukujutuli ja liidese materjal sisemine sein täielikult ja vahutavus ei ole väiksem kui spetsifikatsioonis määratud pikkus. (2) Test a. Pärast seda, kui põhjalik torustik on nõuetele vastav, tehakse katse. Katsepea peab olema 2 m kõrgusel integreeritud toru galeriist. Kui ülesvoolu integreeritud torukujulise toru üleviimise kõrgus kuni kontrollpunkti on väiksem kui 2 m, vastavalt kohaliku inseneri kvaliteedikontrolli ja aktsepteerimise standardile "suletud veekatte veetaseme hüdraulikateedele ehitusnõuete täitmiseks. b. Alusta ajastust, kui katsepea jõuab kindlaksmääratud tasemeni, jälgida integreeritud torukujulise toru leket kuni vaatluse lõpuni. Selleks ajaks tuleb vesi integreeritud torustikule pidevalt tarnida, et katsepea oleks püsiv ja lekkeaeg ei oleks alla 30 minuti. c. Arvutage mõõdetud vee sissevooluava järgmise valemi järgi: q = W / TL, kus q on mõõdetud vee lekkevool [L / (min.m)]; W - vee kogus (L); T - vaatlusaeg (min) L - katsekeha otsa pikkus (m). c. Pärast integreeritud torupaigalduse lõpuleviimist teavitatakse kolmandat kontrollipooli ja lepinguosalise A määratud kohapealset järelevalvet aja jooksul, et viia läbi integreeritud torude galerii süsteemi suletud veekatse. Pärast katse lõpetamist teostab mullatööde ehitusosaline integreeritud torukujulise kraaviku tagasitäitmise. (3) Kontrollpunktid a. Integreeritud torude galeriit tuleb kontrollida sektsioonide kaupa; b. Integreeritud torukujude ja inspekteerimislaevade välimus on kvalifitseeritud ja vee lekkimine ja tõsine vee lekkevool ei ole kvalifitseeritud; c. Mõõdetav aeg pärast vee täitmist torude integreeritud torustikus Raudbetoonitoru torude keetmise aeg ei tohi olla väiksem kui spetsifikatsioonis kindlaksmääratud pikkus; d. Kohapeal viiakse läbi laiaulatuslik torgalerii suletud veekatse, et mõõta tegeliku summa ja välja arvutamist ning täita asjakohased vormid varjatud aktsepteerimise rekordina. (4) Suletud veekatse teade Suletud veekogu suletud sektsioon ei ole tihe ja tihti tähelepanuta jäetud, kuna see asub kaevu. Kui tellisetti kasutatakse tihendamiseks, tuleks tähelepanu pöörata järgmistele punktidele: Düüs peab enne blokeerimist olema 0,5. Toru sisesein vahemikus m puhastatakse, tsemendipüree on värvitud ja kasutatud tellised on niisked kasutamiseks. Müüritel peab olema vähemalt M7.5 ja neil peab olema hea konsistents. Tihendusmört kokkutõmbamiseks ja krohvimiseks peab olema vähemalt M15. Kui toru läbimõõt on suur, peavad sisemised ja välimised küljed olema väikesed ning kasutama tuleks ainult välimist külgühendust või pinda. Pind tuleb rakendada veekindla 5-kihilise konstruktsiooniga. Kui tingimused seda võimaldavad, saab selle enne kvaliteetse kvaliteedi tagamist kaevude kontrollimist pitseerida. Eelseadistatud äravooluava tuleks kontrollida toru sisemises põhjas, et see tühjendada ja katsetada. (5) Veetorude töötlemine integreeritud torude galeriis. Suletud veekatsed on tervikliku torukujunduskontrolli ja materjalide kvaliteedi kontroll. In the event of leakage, the leaks should be marked first and carefully treated after draining the water in the integrated pipe gallery. After the treatment, the test is repeated, and the process is repeated until the water is closed. Third, the material quality: 1, steel; the use of tensile strength is not lower than HRB400 three-stage threaded steel or hot-rolled, cold-rolled ribbed steel, steel properties should meet the requirements of GB1499.2, GB13788, GB1499.1. 2, cement; should use Portland cement, ordinary Portland cement, can also use sulfate-resistant Portland cement, fast-hardening cement. Cement performance should meet the requirements of GB175 and GB748 respectively. 3, aggregate; fine aggregate should use medium coarse sand, fineness modulus 2.3~3.3, mud content is not more than 2%; the maximum particle size of coarse aggregate should not exceed 1/3 of wall thickness of reinforced concrete box culvert, It shall not be greater than 3/4 of the net spacing of the hoop reinforcing bars, the mud content is ≤1%, the stone powder content is ≤5%, the needle-like particle content is ≤10%, and the porosity is ≤45%. 4. Admixtures and admixtures; concrete may not have harmful effects on box culverts when admixtures and admixtures are added. Should comply with the provisions of GB8076. When adding the sodium and polycarboxylate water reducing agent, the amount of addition should be determined after the test; the amount of FDN-2 superplasticizer is 0.75%~1%. The polycarboxylic acid series water reducing agent should be based on The amount of dilution of the mother agent is determined. 5. Water: Concrete mixing water should meet the requirements of JGJ63. 4. Box culvert standard: 1. Appearance quality inspection is as follows: (1) The inner and outer surfaces of the box should be dense, smooth and clean, free from cracks, honeycombs, pockmarks, pores, sinks, exposed sand, exposed stones, exposed pulp and sticky skin. . (2) The end face of the socket should be clean and free of angles. Cracks, exposed ribs, etc. are not densely realized. The groove of the adhesive strip of the socket should be smooth and smooth, the grain is clear, and there should be no sticking of floating pulp and debris. (3) The inner and outer surfaces of the top and bottom plates should be flat and free from local unevenness. (4) The sidewall pre-embedded screws should be firm, the silk path should be smooth and neatly arranged. (5) The tension hole should be smooth, the aperture is consistent, and there is no skew deviation.
2, product size deviation (1) steel frame: height ± 5mm, length ± 5mm, width ± 3mm, reinforced bar ± 5mm, steel bar diameter ± 0.1mm (2) box culvert: height ± 5mm, length ± 2mm, width ±2mm, socket depth ±1mm, socket length ±1mm, wall thickness ±1mm. (3) Box culvert parameter concrete 28d compressive strength C45/, demoulding strength requirement reaches 20Mpa, impermeability When P6 is reached, the freezing and thawing reaches F100, the external pressure crack load reaches 85kn/m, and the failure load reaches 120kn/m. First, the venue settings
19e0885965a9620c7b4ea459ffc0934f.jpg
Prefabricated site
1. The site is selected according to the actual situation of the project. The site adopts closed management to set up import and export, and the construction access road is reserved in the site planning area, and various signs are hanged at the import and export according to regulations. 2. The layout of the prefabrication site shall be in strict accordance with the requirements of the standard factory, meet the requirements of occupational health and safety and environmental management system and HSE operation instructions, and set up various safety environment protection facilities. It shall be fully equipped to meet the requirements of safe and civilized production, sewage discharge and garbage disposal. Strictly in accordance with the relevant provisions of local government departments. 3. Clean the prefabricated site, leveling, vibrating and compacting, laying a 20cm thick cement stabilized macadam base, smoothing and vibrating and compacting. The main road of the plant will pour 15cm thick C20 commercial concrete on the cement stabilized macadam base. , installation area, prefabrication, production area, integrated pipe gallery natural conservation placement area pouring 10cmC20 commercial concrete. In the gantry crane rail erection position, the excavation depth is 60cm, and the concrete is poured and the track is laid. We must also do these three things: (1) The site needs to be cleaned and leveled, including prefabricated sites, connecting construction work belts and existing transportation roads, and passages in prefabricated sites. (2) In the prefabricated site, the stones, weeds, trees, structures, etc. that affect the passage or construction work of the construction machinery should be cleaned up, the ditch and the ridge should be leveled, and the low-lying areas with accumulated water should be drained and filled, if necessary, changed. Fill in, fully guarantee the flatness of the ground and the load-bearing and compressive capacity. (3) Pre-fabrication site cleaning and leveling shall be carried out to save land acquisition or land occupation, no traffic obstruction, no damage to buildings, facilities, monuments, etc., to prevent environmental pollution and soil erosion. 4. Prefabrication of the steel bar processing and installation area, integrated pipe gallery prefabrication production steaming area, integrated pipe gallery natural conservation shed, integrated pipe gallery storage area and other functional areas. The office area and living area are set according to the actual situation, and the prefabricated field entrance and exit is set up as a guard room. Second, the production process
Production process flow chart
1. Reinforcement engineering construction materials entering the site, sampling inspection, steel processing, steel bar binding, installation. (1) Reinforcement approach inspection a. Rebar is hot-rolled HPB300 grade steel and hot-rolled HRB400 grade steel bar. The standard strength of steel bar meets the requirements of 4.2.2 of GB50010-2010. The ribbed steel bar complies with the steel for reinforced concrete: Part II: Hot-rolled ribbed steel bars (GB1499.2-2007); light-round steel bars meet the requirements of steel for reinforced concrete: Part I: Hot-rolled ribbed steel bars (GB1499.1-2008). The steel plate is made of Q235-B steel, the welding electrode HPB300 grade steel is welded with E43 type electrode, and the HRB400 grade steel is welded with E55 type electrode. b. Before the steel enters the site, check the variety, grade, specification, quantity and material list in strict accordance with the requirements, whether the product quality certificate, the factory inspection report and the re-inspection report are complete and valid. The mechanical properties test must be in accordance with the relevant standards. c. Before the steel enters the field and before use, check the appearance quality of the steel bar, whether it is straight, no damage, no slag inclusion on the surface, heavy skin, crack, oil stain, granular or flake old rust, uniform color, view the diameter of the steel bar Meet the requirements, so as not to affect the strength of the steel and anchoring performance. Steel plates, welding rods, etc. are inspected with the steel bar inspection items before entering the site. (2) Storage of steel bars a. The steel bars entering the site are stored in the steel bar storage area according to the variety, specification and grade. The materials are stored by the material staff and the custodians. The steel bar is required to be covered with a pad to prevent rust. b. Check whether the steel bar has the factory certificate and the factory inspection report and the re-inspection report. Check the appearance quality and the volume representative diameter. The steel bar must be inspected comprehensively for its quality index. According to the batch inspection, the diameter and weight deviation are the same as the same factory, the same furnace number, the same specification, the same production process, and the 60-ton steel bar entering the same construction site at the same time is an inspection lot, less than 60 tons. Also as a test lot, carry out witnessed sampling. Sampling of steel bars shall be carried out by the supervising engineer. Two steel bars shall be taken to take two tensile test pieces, each with a length of about 450 mm, and two cold-bent test pieces with a length of about 350 mm, placed in the test box, and then supervised for sealing or monitoring the test room. If the result of the re-examination report is unqualified, it shall be double-sampled and re-tested. The results of the re-examination report shall be qualified, and the professional supervision engineer shall sign the approval, and the batch of steel bars may be used in processing. Storage and storage of other materials shall be carried out by means of moisture insulation. (3) Rebar processing Before processing, according to the design specifications and length and quantity, combined with different processing techniques, the length of each rebar is determined by calculation to ensure accuracy. During processing, check whether there is any error or omission in the blanking table. Check the material table for each type of steel bar. After these two inspections, press the material table to release the real sample. After the trial production is qualified, it can be processed in batches. Good steel bars should be stacked neatly and orderly. The surface of the steel bar should be clean, and the grease, dirt and rust must be cleaned before use. The steel bars are straightened and mechanically straightened. The steel bars after straightening shall not have local bending, dead bends or small waves. The steel bar cutting should be based on the steel bar number, diameter, length and quantity. The length and length of the steel bar should be broken and the short material should be broken first, and the short steel head should be reduced and shortened as much as possible to save steel and reduce loss. When the steel bar is bent, stake out determines the bending point and determines the bending angle based on the rebound strength of each steel bar. Before the formal bending, the steel bars that have been bent in large quantities will be subjected to trial bending and the relevant technical data will be determined before batch bending. After the steel bar is bent, the arc forms an arc. After the bending, the size is not larger than the blanking size. The bending adjustment value should be considered. The bending diameter D of the bent steel bar and the bend of the middle part is not less than 5 times the diameter of the steel bar. The length of the steel bar should be considered comprehensively according to the size of the component, the thickness of the protective layer, and the adjustment value of the bending of the steel bar. The allowable deviation of steel bar processing shall not exceed the specification. For steel bars with insufficient finished material, the butt joint pressure welding method is used to butt the foot length and then bend. The butt welder must be trained in a special butt welding process and sampled for inspection. After the various steel bars are formed, the allowable deviation shall not exceed the specification: the full length of the force ribs shall be ±10 mm; the deviation of the length of each part of the stirrups shall be ±5 mm; the deviation of the bent ribs shall be ±20 mm of the member, large volume The concrete is ±30mm; the deviation of the steel corner is 3mm; the 6~12mm round rib is made into the stirrup, and the length of the end hook is 75~105mm according to the diameter of the main rib. The specific calculation before the blanking is determined, the processed steel bars are classified and stored, and the formed steel bars are prevented from being deformed during storage and transportation.
Braided skeleton (reinforced steel) steel formwork
Difficulties: The difficulty in making the main ribs of the rectangular top pipe is the outer rib main rib. Each ring consists of four steel bars with two arcs each forming a rectangular top pipe rebar ring. The radius of the arc is too small, the curved arc segment is short, and the precision is high. . Solution: Before the steel bars are bent, mark them at the intersection of each arc. Then, the R90 degree arc is bent by three-roll bending, and the straight line segment is not bent. After the arc is fully bent, it is placed on the standard master inspection. After the requirements are met, the moving wheel movement position mark is made on the bending machine operating platform for the next quick production. The three-roll bending machine needs to have the function of jog and reverse. (4) Steel bar welding The formed steel bar is placed on the steel bar welding work tool according to the construction drawings for welding. The welding quality is an important part to ensure the overall strength of the steel bar. In the steel bar processing factory, the steel bars are mainly cleaned by double-sided flash butt welding to clean the corner burrs and the end face rust, oil stains and oxide film before being welded, and the metal luster is exposed by grinding, and there is no oxidation phenomenon. At the same time, the end face of the steel bar should be flattened to facilitate a good combination. The fixtures on both sides should be aligned to ensure that the two steel bars are on the same axis, and the local clearance of the two steel bars is not more than 3 mm. The pressure applied during the welding should be uniform and strong, and the temperature should be controlled at 30-40 MPa depending on the diameter of the steel bar to achieve good adhesion between the two steel bars. When the steel bars of different diameters are butt welded, the deviation shall not exceed 7mm. Butt welding and spot welding are strictly in accordance with the regulations, and the welding personnel are certified to work. After the welding is completed, the joint will be changed from white to black to release the clamp, and the steel bar will be taken out smoothly to avoid bending. After the welding of the steel bars is completed, the appearance inspection of the welded joints shall be carried out in time, and the joints that fail the visual inspection shall be re-welded. All welding operators must ensure that all types of welding machines are in good working condition, master the main performance and parameters of various welding machines in time, and select the best parameters for actual operation according to the conditions of the base metal and weather to ensure the welding quality. . (5) Reinforced steel cages should be re-calibrated before specification, size, shape, quantity, positioning tooling, etc., and comprehensive inspection should be carried out according to the design drawings and ingredient list. The design, ingredient list and physical object can be matched. Security. Before the system is installed, the reinforcement is arranged on the positioning tooling platform according to the design data. At the same time, according to the location, the setting of the standing reinforcement is determined to ensure that the steel bars after the installation meet the requirements. In the process of security, the steel bars are mainly made by wire binding and spot welding. The holes are made of 20~22# wire. The method of binding and binding is in accordance with the specifications and regulations. Spot welding is mainly used for forming steel bars and standing bars. The fixing, the spot welding should be firm, the points should be evenly distributed, and the force ribs should not be seriously damaged. The lashing joint of the steel bar shall meet the following requirements: a. The end of the lap length shall be not less than 10 times the diameter of the steel bar at the bend of the steel bar, and the joint shall not be located at the maximum bending moment of the component. b. In the tension zone, the end of the I-grade steel lashing joint shall be made into a hook. In the same section, the cross-sectional area of the joint of the tension zone shall be less than 50% of the total area of the force-receiving joint, and the lashing joint shall not be more than 50%. Not more than 25%, at the same time, the lashing joints must not exceed 50% in the compression zone. c. Reinforced joints, tied with wire at the center and at both ends. d. The joint positions of the stressed ribs are staggered from each other. The lap length of the tensioned steel reinforced joints should meet the structural design requirements. The welded steel joints and mechanical joints should be placed at the minimum bending moment and staggered. e. When the diameter of the stressed steel bar is ≥25mm, it is not advisable to use a non-welded lashing joint. f The thickness of the concrete protective layer of the stressed steel bar should meet the structural design requirements. In order to ensure the correct position of the steel bar, it is tied and installed according to the design requirements. g. In the reinforcement cage binding process, one ΦPVC pipe is pre-buried on the four sides of the joint, Φ14mm, the length of the PVC pipe is determined according to the wall thickness of the mouth of the joint, and the pre-embedded PVC pipe is used as the inspection hole and the injection hole. The lifting holes are installed at 500mm above and below the central axis of the left and right sides of the integrated pipe gallery. Two Φ125*10mm*220mm steel pipes are welded to the steel frame, and Φ140*4 steel plate is used for sealing. The Φ125*10mm*180mm steel pipe is installed before lifting. Φ110mm*350mm iron pin is used as the integrated pipe hanger ear to meet the hoisting construction of the integrated pipe gallery. Reinforced steel works are concealed projects. Before pouring concrete, the steel bars and embedded parts should be inspected and accepted, and the hidden engineering records should be made. After the on-site supervision engineers agree, the next process can be carried out.
92074dd65836ec55b1746a4e64e64b32.jpg
Steel mold assembly
The most efficient method for the assembly process should be: first support the inner mold, the steel collar connection ribs should be welded first and then placed in the bottom mold, and the lining steel ring connecting ribs of the socket should be welded after the steel frame is put into the mold, and the steel bars are welded. After the skeleton is put into the mold, the grouting hole, the grouting hole and the pre-embedded steel plate are welded. After the welding, the outer mold is assembled. In order to prevent the position of the lifting hole from being inaccurate, the lifting hole is fixed on the outer mold, and the outer mold is assembled and then the welding socket is pre-prepared. Buried steel ring. (6) Reinforced protective layer The protective layer of concrete is made of concrete block, the thickness is equal to the thickness of the designed protective layer, the block size is 3cm×3cm, the pad number is more than C25 mortar strength, and the curing is strengthened during production to achieve design strength. 85% of the above can be used. When used in the vertical structure, the 20# binding line can be buried in the block, and the block is tied to the steel bar with the wire. The bottom layer of the bottom plate and the wall reinforcement layer are placed one square meter per square meter, and the plum blossoms are arranged. The spacing of the pads should be properly encrypted. Reasonably arrange the blocks, and tie them tightly on the stressed steel bars, instead of being placed on the non-stressed tendons, the fixing should be firm to prevent displacement and slippage during the pouring process; whether the blocks are fully inspected before concrete pouring Missing or damaged. 2. Concrete pouring (1) Concrete material Concrete transportation is transported to the prefabricated site by concrete tanker, and pumped into the warehouse by concrete pump truck. The slump of concrete is generally controlled between 140 and 180 mm (the specific value depends on the temperature of the day). 4 concrete vibrating rods with a vibrating radius of 20-25cm, so the spacing between each rod is 40cm. Each rod depth is within 5cm below the previous vibrating surface, and the vibrating time per rod is 2-3 minutes. (2) Mixing ratio design and test a. Mixing ratio design To meet the requirements of concrete design strength, frost resistance, impermeability, sand aggregate expansion rate and construction workability, the concrete construction mix ratio optimization test At the same time, it meets the requirements of construction water-cement ratio and slump, and is reviewed and approved by the supervision engineer. The mix ratio of concrete should ensure that the concrete obtained can meet the specific pouring conditions, and the water consumption in the concrete mix ratio is as small as possible. b. Concrete mix ratio test concrete mix ratio test plan, including concrete mix ratio test and concrete performance test of different strength grades, blending ratio test 14d ahead of the various mix ratio test ingredients and mixing, molding and maintenance, etc. The mix ratio test plan is reported to the supervision engineer. c. Construction mix ratio control According to the mix ratio test and the batch list approved by the supervision engineer, the concrete mix ratio is controlled, and the total water consumption is adjusted according to the water content of the aggregate. Concrete slump is determined by the nature of the structural part, the rate of reinforcement, the concrete transport and casting method, and the climatic conditions, and uses a small slump as much as possible. Concrete slump meets the requirements of SL677-2014. (3) Concrete sampling test During the concrete pouring process, the contractor shall carry out concrete sampling test at the discharge opening and pouring site according to the provisions of SL352-2006 and the instructions of the supervisor, and submit the following materials to the supervisor: a. And the quality certificate of its integrated pipe gallery; b. The composition, mixing and dimensions of the test piece; c. Description of the preparation and maintenance of the test piece; d. Test results and description; e. Concrete of various ages Test data such as bulk density, compressive strength, tensile strength, ultimate tensile value, elastic modulus, Poisson's ratio, slump and initial setting and final setting time. (4) Concrete pouring a. The mix ratio of commercial concrete should meet the requirements of DL/T5330-2005 "Design Specification for Hydraulic Concrete Mixing Ratio", and use cement and water reducing agent with relatively early initial setting time and early strength increase after final setting. Various additives such as air entraining agent and early strength agent should consider the long distance of concrete transportation, increase the early strength of concrete, reduce the time of demoulding, shorten the construction period, and especially solve the slow growth of concrete strength during winter construction. The problem with the site concrete slump is to be controlled at 140-180mm. b. After the mold and steel bars have been installed and qualified by the technicians for quality inspection and supervision, and confirmed, the integrated pipe gallery can be poured. The height of the hole is 2m or more above the ground, and the drop is 2m or less. The soft string barrel is set at the mouth to ensure that the concrete has a falling height of less than 2m. c. The concrete pipe tunnel concrete shall adopt the symmetric casting method to consider that the height of the edge should not exceed 40cm, and the construction by continuous casting method should not be intermittent. d. Concrete is poured in layers, in a certain direction, and with a certain thickness. The concrete is horizontally layered and the layer thickness is 30-40 cm. e. Vibrating uses a plug-in vibrating rod, the moving distance does not exceed 1.5 times the radius of action of the vibrating bar, and maintains a distance of 5 to 10 cm from the side mold. Insert the lower layer of concrete 5 to 10 cm when vibrating, and slowly propose the vibrating bar after each vibration. Avoid vibrating the formwork, steel bars, etc. during vibration; for each vibration part, it must be oscillated until the concrete is compacted, that is, the concrete stops sinking, no bubbles appear, and the surface is flat and muddy. During the pouring process, each work type should be arranged to check the changes of steel bars, brackets and stencils, and the situation should be dealt with in time. 3, box culvert maintenance and demoulding
Box culvert prefabricated
(1) After the concrete is poured, after the concrete is initially set, the integrated pipe gallery is steamed at a high temperature. The steaming adopts a customized steaming cover, and the integrated pipe gallery mold is covered with a steaming cover, and the bottom of the steaming cover is sealed to prevent steam from being discharged during the steaming process. The steaming boiler is steamed for the environmentally friendly steaming facility. support. In the process of steaming, it is divided into four stages: static stop, warming, constant temperature and cooling. During the static stop, the ambient temperature should be kept below 5 °C, and the temperature rise should be controlled within 15 °C/h. Constant temperature: When the temperature reaches 60 °C, the steaming can be stopped after four hours of constant temperature steaming. Cooling: The cooling rate of the integrated pipe gallery in the steaming shed is less than 10 °C / h, and the surface temperature of the integrated pipe gallery is not more than 5 °C, so that the integrated pipe gallery can be removed from the steaming cover. During the steaming process, special personnel are arranged to effectively control the temperature rise and fall and record in detail. Firstly, after the integrated pipe gallery has been poured and stopped for 2 hours, the integrated pipe gallery has been initially set and the inspection has no abnormality. The steaming cover and equipment are moved to the prefabricated production area, and the integrated pipe gallery has been set up with the steaming cover. Strictly sealed, check the sealing condition of steaming equipment and steaming cover and debug the steaming equipment. After all the preparations are in place, start the steaming equipment to heat up, and pay attention to control the heating rate within 15 °C/h during the heating process. . It is forbidden to heat up too fast or too slow, which will affect the compressive strength and performance of the integrated pipe gallery. When the temperature reaches 60 °C, the constant temperature steaming is started. After the constant temperature steaming for four hours, the steaming can be stopped. After the constant temperature steaming is finished, the integrated pipe gallery is cooled and maintained in the steaming shed, and the cooling rate is strictly controlled. Within 10 °C / h, the temperature drops to the surface temperature of the integrated pipe gallery and the ambient temperature does not exceed 5 °C, the steaming cover can be removed, and the integrated pipe gallery is demolished and moved to a natural conservation shed for natural conservation. (2) After the steaming is completed, the pipe gallery demoulding and natural conservation shed maintenance plan will reach 50% of the design strength and the temperature difference between the inside and outside of the steaming cover can not be more than 5 °C after stopping the steaming for one hour. mold. The order of demolding is from the inside out, from top to bottom. In the process of dismantling, it should be removed step by step in order, the mold is removed, the prefabricated integrated pipe gallery and the bottom mold are removed from the mold by the gantry crane, and transported to the designated natural conservation shed for natural watering. It is strictly forbidden to use the crowbar to hit the stencil under the template during the demoulding process. After the natural maintenance reaches 75% of the design strength, the integrated pipe gallery will be removed from the natural conservation shed for reversal. (3) Folding and placing plan of the pipe gallery After the concrete pouring is completed, the design strength is 50% and after the steaming is stopped for one hour, the temperature difference between the inside and outside of the steaming shed can not be greater than 5 °C, and the mold can be demolished. The order of demolding is from the inside out, from top to bottom. In the process of dismantling, it should be removed step by step in sequence. After the mold is removed, the prefabricated product and the bottom mold are lifted out of the mold and transported to the designated natural conservation area for natural watering. It is strictly forbidden to use the crowbar to hit the stencil under the template during the demoulding process. The angular parts of the sling or wire rope contact are protected by a pad, which is light and light during the lifting process, and all actions are directed by a special person. After the product strength reaches 75% of the design strength, the product is transferred to the finished natural conservation area. Move the product out of the tray during transport and flip the product. In order to facilitate the storage of the product, the original product of the product is turned over to the bottom of the floor, and the product storage height is two layers. 4, closed water testing standards
Closed water inspection flow chart
(1) Water injection in the integrated pipe gallery Before the water injection, the integrated pipe gallery block is sealed and sealed. After passing the inspection, water is injected into the integrated pipe gallery. The water is injected from the lower end of the integrated pipe gallery. After the water is filled, the inner wall of the integrated pipe gallery and the interface material are fully absorbed, and the soaking time is not less than the length specified in the specification. (2) Test a. After the comprehensive pipe shed is in compliance with the requirements, the test shall be carried out. The test head shall be 2 m above the top of the integrated pipe gallery. If the height from the top of the upstream integrated pipe gallery to the inspection port is less than 2 m, according to the municipal engineering quality inspection and acceptance Standard “closed water test water level to the wellhead to meet construction requirements. b. Start timing when the test head reaches the specified level, observe the leakage of the integrated pipe gallery until the end of the observation. At this time, the water should be continuously supplied to the integrated pipe gallery to keep the test head constant, and the seepage time of the water seepage is not less than 30 minutes. c. Calculate the measured water seepage according to the following formula: q=W/TL where q is the measured water seepage [L/(min.m)]; W——the amount of water (L); T——observation time (min) L - length of the test tube end (m). c. After the completion of the integrated pipe gallery, the third inspection party and the on-site supervision designated by Party A shall be notified in time to carry out the closed water test of the integrated pipe gallery system. After the test is completed, the earthwork construction party shall carry out the backfilling of the integrated pipe gallery trench. (3) Checkpoints a. The integrated pipe gallery must be inspected section by section; b. The appearance quality of the integrated pipe gallery and inspection well has been qualified, and no water leakage and no serious water seepage are qualified; c. Soaking time after filling the water in the integrated pipe gallery The immersion time of the reinforced concrete pipe shall not be less than the length specified in the specification; d. The comprehensive pipe gallery closed water test shall be carried out on site to measure the actual amount and the field calculation, and fill in the relevant forms as a concealed acceptance record. (4) Notice of closed water test The closed section of the closed water section is not dense, and it is often neglected because it is in the well. If the brick wall is used for sealing, the following points should be paid attention to: The nozzle should be 0.5 before the blockage The inner wall of the pipe in the range of m is cleaned, the cement puree is painted, and the bricks used are wetted for use. The masonry mortar should be no less than M7.5 and have a good consistency. The cement mortar for jointing and plastering shall be not less than M15. When the diameter of the pipe is large, the inner and outer sides should be small and only the outer one-side joint or the surface should be used. The surface should be applied in a waterproof 5-layer construction method. When conditions permit, it can be sealed before the inspection of the wells to ensure quality. The preset drain hole should be inspected at the inner bottom of the tube for draining and testing. (5) Treatment of water seepage in integrated pipe gallery The closed water test is a comprehensive inspection of the construction of integrated pipe gallery and the quality of materials. In the event of leakage, the leaks should be marked first and carefully treated after draining the water in the integrated pipe gallery. After the treatment, the test is repeated, and the process is repeated until the water is closed. Third, the material quality: 1, steel; the use of tensile strength is not lower than HRB400 three-stage threaded steel or hot-rolled, cold-rolled ribbed steel, steel properties should meet the requirements of GB1499.2, GB13788, GB1499.1. 2, cement; should use Portland cement, ordinary Portland cement, can also use sulfate-resistant Portland cement, fast-hardening cement. Cement performance should meet the requirements of GB175 and GB748 respectively. 3, aggregate; fine aggregate should use medium coarse sand, fineness modulus 2.3~3.3, mud content is not more than 2%; the maximum particle size of coarse aggregate should not exceed 1/3 of wall thickness of reinforced concrete box culvert, It shall not be greater than 3/4 of the net spacing of the hoop reinforcing bars, the mud content is ≤1%, the stone powder content is ≤5%, the needle-like particle content is ≤10%, and the porosity is ≤45%. 4. Admixtures and admixtures; concrete may not have harmful effects on box culverts when admixtures and admixtures are added. Should comply with the provisions of GB8076. When adding the sodium and polycarboxylate water reducing agent, the amount of addition should be determined after the test; the amount of FDN-2 superplasticizer is 0.75%~1%. The polycarboxylic acid series water reducing agent should be based on The amount of dilution of the mother agent is determined. 5. Water: Concrete mixing water should meet the requirements of JGJ63. 4. Box culvert standard: 1. Appearance quality inspection is as follows: (1) The inner and outer surfaces of the box should be dense, smooth and clean, free from cracks, honeycombs, pockmarks, pores, sinks, exposed sand, exposed stones, exposed pulp and sticky skin. . (2) The end face of the socket should be clean and free of angles. Cracks, exposed ribs, etc. are not densely realized. The groove of the adhesive strip of the socket should be smooth and smooth, the grain is clear, and there should be no sticking of floating pulp and debris. (3) The inner and outer surfaces of the top and bottom plates should be flat and free from local unevenness. (4) The sidewall pre-embedded screws should be firm, the silk path should be smooth and neatly arranged. (5) The tension hole should be smooth, the aperture is consistent, and there is no skew deviation.
2, product size deviation (1) steel frame: height ± 5mm, length ± 5mm, width ± 3mm, reinforced bar ± 5mm, steel bar diameter ± 0.1mm (2) box culvert: height ± 5mm, length ± 2mm, width ±2mm, socket depth ±1mm, socket length ±1mm, wall thickness ±1mm. (3) Box culvert parameter concrete 28d compressive strength C45/, demoulding strength requirement reaches 20Mpa, impermeability When P6 is reached, the freezing and thawing reaches F100, the external pressure crack load reaches 85kn/m, and the failure load reaches 120kn/m.


















